Kate G. - March 31 2024

Flash Firmware for the THR Board on the Kingroon KP3S Pro V2 and KLP1

Flash Firmware for the THR Board on the KINGROON KP3S Pro V2 and KLP1.jpeg__PID:beb6ef18-8156-4702-a1e7-56ba61d3aa1e

MThe THR board defines a lot of settings of the Klipper printing. It is used in the KINGROON KP3S Pro V2 and KLP1 3D printers, provides powerful features. This tutorial will show you how to flash its firmware and set it up.

Since the operation may damage the board, if you only have 1 THR board or your printer works well, we do not recommend you flash it.

Things You Need:

Before start, please prepare the things as below:

Flash Firmware for the THR Board on the KINGROON KP3S Pro V2 and KLP1

1) a new USB cable
The USB cable should have the function of data transfer, otherwise it may only have 2 cables inside.
2) a new THR cable
If you can manage to build your own, skip it. Just make sure the required pins connected well
3) a THR board
You must be very careful if you have no extra THR board
4) a 3 pin terminal with cables
You need to power up the board with its “PROBE” port, it is “blank”, “negative” and “positive” from the left to right. If you cannot find a same terminal like that or cannot build your own cables, cutting it form the leveling sensor of the KP3S Pro V2 and KLP1 would be an option.

Flash Firmware for the THR Board on the KINGROON KP3S Pro V2 and KLP1.jpeg__PID:beb6ef18-8156-4702-a1e7-56ba61d3aa1e

5) Downloading the THR Board Firmware from this link: https://1drv.ms/f/s!AmGcVrncIH3ZlAKlZKuVNyPkplPI?e=A8qaix

Wiring the Cable:

Step 1, cutting the USB cable, you should be able to get four cables, two of them are red and black, they are positive and negative; The rest two are for data transfer.
Step 2, cutting the sensor, remove the left side cable, then connect them to the USB cable as the above photo.
Step 3, cutting the THR cable and leave the green(D-) and yellow(D+) cable only.

Flash Firmware for the THR Board on the KINGROON KP3S Pro V2 and KLP1.jpeg__PID:beb6ef18-8156-4702-a1e7-56ba61d3aa1e

Connection Checking:

Step 1, connect the USB cable to your PC. If the board becomes hot, then you are in a wrong connection, switch the cables of on the “PROBE” port. If the green light on the board turns on, the connection is correct.

Step 2, hold the “boot” button, connect the USB cable to your PC. If the “RPI-RPI2” USB drive shows up, your connection is correct, or you need to switch the cables connect to the green cable and yellow cable

And you can see the boards information from the device manager.

After that, disconnect the connection, use heat-shrink tubes or electric tape to fix the wiring.

Flashing the Firmware:

Now you are all set. Hold the “boot” button, connect the board to your PC, then drag the “klipper.uf2” file into the “RPI-RPI2” USB drive. The drive should be disconnected immediately, just wait for a few seconds, the flashing is finished.
If you do the connection again, there should be now firmware file in the drive now.

Step 2, enter “ls /dev/serial/by-id/*”, you will get a serial number, mine is “/dev/serial/by-id/usb-Klipper_rp2040_75034E152C886258-if00”

Copy that number.
After that, open the “MKS_THR.cfg” file from the Klipper dashboard, replace the current serial number. Then you are all set.

32GB EMMC Module for KP3S Pro V2 and KLP1
32GB EMMC Module for KP3S Pro V2 and KLP1
32GB EMMC Module for KP3S Pro V2 and KLP1
32GB EMMC Module for KP3S Pro V2 and KLP1
32GB EMMC Module for KP3S Pro V2 and KLP1
32GB EMMC Module for KP3S Pro V2 and KLP1
32GB EMMC Module for KP3S Pro V2 and KLP1
32GB EMMC Module for KP3S Pro V2 and KLP1
32GB EMMC Module for KP3S Pro V2 and KLP1
32GB EMMC Module for KP3S Pro V2 and KLP1
32GB EMMC Module for KP3S Pro V2 and KLP1
32GB EMMC Module for KP3S Pro V2 and KLP1

32GB EMMC Module for KP3S Pro V2 and KLP1

$12.00

32GB EMMC Module for your KINGROON KP3S Pro V2 and Kingroon KLP1 3D printers. It also fit MKS board with the same type of EMMC Module. You can expend the system storage to 32GB for your KP3S Pro V2 and KLP1, which is much larger than its original 8GB size. It is highly recommend for those who wants to take time lapse video with the Klipper system or have large amount of data to storage.

Compatible with:
MKS EMMC Adapter 1.0 for KINGROON KP3S Pro V2 and KLP1

To flash the EMMC Module, use high speed and high quality SD card adapter to mount it.

Check the below tutorial to get system image and know how to proceed:
How to Falsh the EMMC Chip on Kingroon KP3S Pro V2 and KLP1

View Details
MKS EMMC Adapter 1.0 for KINGROON KP3S Pro V2 and KLP1
MKS EMMC Adapter 1.0 for KINGROON KP3S Pro V2 and KLP1
MKS EMMC Adapter 1.0 for KINGROON KP3S Pro V2 and KLP1
MKS EMMC Adapter 1.0 for KINGROON KP3S Pro V2 and KLP1
MKS EMMC Adapter 1.0 for KINGROON KP3S Pro V2 and KLP1
MKS EMMC Adapter 1.0 for KINGROON KP3S Pro V2 and KLP1
MKS EMMC Adapter 1.0 for KINGROON KP3S Pro V2 and KLP1
MKS EMMC Adapter 1.0 for KINGROON KP3S Pro V2 and KLP1
MKS EMMC Adapter 1.0 for KINGROON KP3S Pro V2 and KLP1
MKS EMMC Adapter 1.0 for KINGROON KP3S Pro V2 and KLP1
MKS EMMC Adapter 1.0 for KINGROON KP3S Pro V2 and KLP1
MKS EMMC Adapter 1.0 for KINGROON KP3S Pro V2 and KLP1

MKS EMMC Adapter 1.0 for KINGROON KP3S Pro V2 and KLP1

$3.00

This is the MKS EMMC adapter for the KINGROON KP3S Pro V2 and KLP1. With this tool you can flash a MKS EMMC chip and rewrite the system in it. For KINGROON users, you can check this link for its tutorial:

Flash Firmware for the THR Board on the Kingroon KP3S Pro V2 and KLP1

Technical Details:
Power: 5V
Port: Micro SD
Requirement: High Speed SD card Reader

View Details
MKSEMMC-ADAPTERV2forKINGROONKP3SProV2andKLP1P6_480x480_7f69db48-8acc-45d2-a716-b241034b8747
MKSEMMC-ADAPTERV2forKINGROONKP3SProV2andKLP1P1_480x480_de51cb20-b30a-4ec5-b5cd-00928996a169
MKSEMMC-ADAPTERV2forKINGROONKP3SProV2andKLP1P2_480x480_7da36024-9a24-4e5a-89be-9c902600a549
MKSEMMC-ADAPTERV2forKINGROONKP3SProV2andKLP1P2_480x480_7da36024-9a24-4e5a-89be-9c902600a549
MKS EMMC-ADAPTER V2 for Kingroon KP3S Pro V2 and KLP1
MKS EMMC-ADAPTER V2 for Kingroon KP3S Pro V2 and KLP1
MKS EMMC-ADAPTER V2 for Kingroon KP3S Pro V2 and KLP1
MKS EMMC-ADAPTER V2 for Kingroon KP3S Pro V2 and KLP1
MKS EMMC-ADAPTER V2 for Kingroon KP3S Pro V2 and KLP1
MKS EMMC-ADAPTER V2 for Kingroon KP3S Pro V2 and KLP1
MKSEMMC-ADAPTERV2forKINGROONKP3SProV2andKLP1P6_480x480_7f69db48-8acc-45d2-a716-b241034b8747
MKSEMMC-ADAPTERV2forKINGROONKP3SProV2andKLP1P1_480x480_de51cb20-b30a-4ec5-b5cd-00928996a169
MKSEMMC-ADAPTERV2forKINGROONKP3SProV2andKLP1P2_480x480_7da36024-9a24-4e5a-89be-9c902600a549
MKSEMMC-ADAPTERV2forKINGROONKP3SProV2andKLP1P2_480x480_7da36024-9a24-4e5a-89be-9c902600a549
MKS EMMC-ADAPTER V2 for Kingroon KP3S Pro V2 and KLP1
MKS EMMC-ADAPTER V2 for Kingroon KP3S Pro V2 and KLP1
MKS EMMC-ADAPTER V2 for Kingroon KP3S Pro V2 and KLP1
MKS EMMC-ADAPTER V2 for Kingroon KP3S Pro V2 and KLP1
MKS EMMC-ADAPTER V2 for Kingroon KP3S Pro V2 and KLP1
MKS EMMC-ADAPTER V2 for Kingroon KP3S Pro V2 and KLP1

MKS EMMC-ADAPTER V2 for Kingroon KP3S Pro V2 and KLP1

$8.00

This is the MKS EMMC-ADAPTER V2, you can use it to flash the EMMC module or read the SD card. If you don't have any high speed or high quality SD card adapter, you will need this adapter.

MKS EMMC-ADAPTER V2 board is a USB 3.0 SD 3.0 Reader for MKS EMMC Module or Micro SD TF Card, has high read and write rates.

Compatible with: Upgrade 32GB EMMC Module for the KINGROON KP3S Pro V2 and KLP1.

Check the below tutorial to get system image and know how to proceed:
How to Falsh the EMMC Chip on Kingroon KP3S Pro V2 and KLP1

Parameters:

MKS EMMC-ADAPTER V2 Parameters
USB interface USB 3.0
Applicable Motherboard MKS EMMC Module, Micro SD TF Card
View Details

Leave a comment

Please note, comments must be approved before they are published