{"product_id":"2pcs-replacement-cutter-tool-blades-for-anycubic-kobra-x-series","title":"2pcs Replacement Cutter Tool Blades for Anycubic Kobra X Series","description":"\u003cp\u003eReplacement cutter tool set for Anycubic Kobra X 3D printers, including two durable cutter assemblies and a protective storage box for neat, safe replacement-part storage.\u003c\/p\u003e\n\u003ch3\u003eCompatibility\u003c\/h3\u003e\n\u003cp\u003eAnycubic Kobra X\u003c\/p\u003e\n\u003ch3\u003ePackage List\u003c\/h3\u003e\n\u003cp\u003eCutter × 2\u003c\/p\u003e\n\u003cp\u003eStorage Box × 1\u003c\/p\u003e\n\u003ch3\u003eKobra X-Hot End Cutter Assembly Replacement Guide\u003c\/h3\u003e\n\u003ch3\u003e1. Tools used:\u003c\/h3\u003e\n\u003cp\u003eH1.5 hex key\u003c\/p\u003e\n\u003cp\u003eH2.0 hex key\u003c\/p\u003e\n\u003cp\u003eH2.5 hex key\u003c\/p\u003e\n\u003ch3\u003e2. Disassembly steps:\u003c\/h3\u003e\n\u003ch3\u003eStep 1: Turn off the printer\u003c\/h3\u003e\n\u003cp\u003eBefore disassembly, please turn off the printer and disconnect the power to ensure safe operation.\u003c\/p\u003e\n\u003ch3\u003eStep 2: Remove the print head front cover\u003c\/h3\u003e\n\u003cp\u003ePress the bottom of the print head front cover and gently pull it forward to remove the print head front cover.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.anycubic.com\/wdcdn.qpic.cn_MTY4ODg1ODA1MzM3OTM4Mw_242087_cYBuMgVv8mfxDYpZ_1764063040.png\"\u003e\u003c\/p\u003e\n\u003ch3\u003eStep 3: Remove the printhead wiring harness\u003c\/h3\u003e\n\u003cp\u003eFind the recess at the back of the print head casing to open it, then remove the print head back cover.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.anycubic.com\/wdcdn.qpic.cn_MTY4ODg1ODA1MzM3OTM4Mw_342635_eMGPcn0CpTZSpq4U_1764149242.png\"\u003e\u003c\/p\u003e\n\u003cp\u003ePress the end clip to remove the print head wiring harness.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.anycubic.com\/wdcdn.qpic.cn_MTY4ODg1ODA1MzM3OTM4Mw_895230_LxYP9WF6Yzz46pKF_1764149816.png\"\u003e\u003c\/p\u003e\n\u003ch3\u003eStep 4: Remove the printhead module\u003c\/h3\u003e\n\u003cp\u003eThe fixing screw is positioned behind the printhead module. Use your hand to hold the printhead module to prevent it from falling off, and use an H2.5 hex key to unscrew the fixing screws.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.anycubic.com\/wdcdn.qpic.cn_MTY4ODg1ODA1MzM3OTM4Mw_927905_j4TQ8Wd5SPECEQ41_1764150316.png\"\u003e\u003c\/p\u003e\n\u003ch3\u003eStep 5: Remove the model's cooling fan\u003c\/h3\u003e\n\u003cp\u003eUnplug the model cooling fan cable, then use an H1.5 hex wrench to unscrew the two screws securing the model cooling fan on both sides to remove the model's cooling fan.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.anycubic.com\/image_6joq9V9z.png\"\u003e\u003c\/p\u003e\n\u003ch3\u003eStep 6: Remove the print head casing\u003c\/h3\u003e\n\u003cp\u003eThen, use an H2.0 hex wrench to unscrew and remove the two screws securing the reversing mechanism, then unscrew the four screws securing the front panel and remove the front panel.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.anycubic.com\/wdcdn.qpic.cn_MTY4ODg1NTQxOTU3MjE3Mw_215710_FFBm-6rvG4NxSp9R_1764554723.png\"\u003e\u003c\/p\u003e\n\u003cp\u003eGently pry off the print head housing, remove the cutter from the shell, then pull the print head shell backward.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.anycubic.com\/image_6Kx090aw.png\"\u003e\u003c\/p\u003e\n\u003ch3\u003eStep 7: Disassemble the hot-end cutter assembly\u003c\/h3\u003e\n\u003cp\u003eFirst, unplug the strain gauge cable shown in the left diagram below, then unplug the heating element and NTC cable from the print head adapter plate at the back.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.anycubic.com\/wdcdn.qpic.cn_MTY4ODg1NTQxOTU3MjE3Mw_647325_eukFB1coBZlY42St_1764666191.png\"\u003e\u003c\/p\u003e\n\u003cp\u003eThen use an H2.0 hex wrench to unscrew the screws securing the strain gauge assembly and remove the strain gauge assembly.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.anycubic.com\/%E4%BC%81%E4%B8%9A%E5%BE%AE%E4%BF%A1%E6%88%AA%E5%9B%BE_17675932492399.png\"\u003e\u003c\/p\u003e\n\u003ch3\u003e3. Installation steps:\u003c\/h3\u003e\n\u003ch3\u003eStep 1: Replace the hot-end cutter assembly\u003c\/h3\u003e\n\u003cp\u003eTo replace the new strain gauge assembly, first place the screws into the holes on both sides, then align them with the two mounting holes on the print head, and use an H2.0 hex wrench to tighten the two screws securing the strain gauge assembly.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.anycubic.com\/image_6C8FCofr.png\"\u003e\u003c\/p\u003e\n\u003cp\u003eThen, connect the strain gauge cable, heating gauge cable, and NTC cable shown below back to the print head adapter board respectively.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.anycubic.com\/wdcdn.qpic.cn_MTY4ODg1NTQxOTU3MjE3Mw_647325_eukFB1coBZlY42St_1764666191.png\"\u003e\u003c\/p\u003e\n\u003ch3\u003eStep 2: Install the print head housing\u003c\/h3\u003e\n\u003cp\u003eReinstall the print head housing from the back, and when the cutter is blocked, gently pry the shell outward to snap the cutter into the groove.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.anycubic.com\/image_6Kx090aw.png\"\u003e\u003c\/p\u003e\n\u003cp\u003eThen, reinstall the reversing mechanism and front panel back into the print head, and use an H2.0 hex wrench to tighten the fixed screws.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.anycubic.com\/wdcdn.qpic.cn_MTY4ODg1NTQxOTU3MjE3Mw_215710_FFBm-6rvG4NxSp9R_1764554723.png\"\u003e\u003c\/p\u003e\n\u003ch3\u003eStep 3: Install the model cooling fan\u003c\/h3\u003e\n\u003cp\u003eReconnect the model cooling fan cable, then use an H1.5 hex wrench to tighten the two screws securing the model cooling fan.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.anycubic.com\/image_6joq9V9z.png\"\u003e\u003c\/p\u003e\n\u003ch3\u003eStep 4: Install the print head module\u003c\/h3\u003e\n\u003cp\u003eFirst, reinstall the print head module and tighten the four screws securing the print head module with an H2.5 hex key.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.anycubic.com\/wdcdn.qpic.cn_MTY4ODg1ODA1MzM3OTM4Mw_487801_IxDCrX_WejAblUxr_1764152303.png\"\u003e\u003c\/p\u003e\n\u003cp\u003eThen connect the print head signal line to the print head adapter board, and reinstall it back into the cover plate.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.anycubic.com\/wdcdn.qpic.cn_MTY4ODg1ODA1MzM3OTM4Mw_333122_A0ZTAb9vPuGOCFSZ_1764225415.png\"\u003e\u003c\/p\u003e\n\u003ch3\u003eStep 5: Install the print head front cover\u003c\/h3\u003e\n\u003cp\u003eAlign the front cover of the print head and snap it in, checking whether both sides are jammed.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.anycubic.com\/wdcdn.qpic.cn_MTY4ODg1ODA1MzM3OTM4Mw_853931_msPjqPdF_nwhipbH_1764127426.png\"\u003e\u003c\/p\u003e","brand":"Anycubic","offers":[{"title":"Kobra X","offer_id":54482563825977,"sku":null,"price":12.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0759\/4531\/2569\/files\/2pcs_-_Cutter_Tool_Blades_for_Anycubic_Kobra_X_Series.jpg?v=1789549299","url":"https:\/\/p3d.mx\/products\/2pcs-replacement-cutter-tool-blades-for-anycubic-kobra-x-series","provider":"P3D","version":"1.0","type":"link"}