{"product_id":"mainboard-for-bambu-a1-mini","title":"Mainboard for Bambu A1 mini","description":"\u003ch3\u003eMainboard Replacement Guide - A1 mini\u003c\/h3\u003e\n\u003cp\u003eThis guide shows how to replace the Main Controller Board on the A1 mini\u003c\/p\u003e\n\u003ch3\u003eIn this guide we will show the process of replacing the Mainboard on the A1 mini\u003c\/h3\u003e\n\u003ch3\u003eWhen to use?\u003c\/h3\u003e\n\u003cp\u003eThis guide should be used if the Mainboard of the A1 mini is faulty, and needs to be replaced.\u003c\/p\u003e\n\u003ch3\u003eCommon issues that are caused by the A1 mini Mainboard are:\u003c\/h3\u003e\n\u003cp\u003ePrinter is not turning on\u003c\/p\u003e\n\u003cp\u003eThe Mainboard is damaged\u003c\/p\u003e\n\u003cp\u003eRecommended by Bambu Lab Customer Support\u003c\/p\u003e\n\u003ch3\u003eTools and materials needed\u003c\/h3\u003e\n\u003cp\u003eBambu Lab Main Controller Board for A1 mini\u003c\/p\u003e\n\u003cp\u003eH2.0 hex wrench\u003c\/p\u003e\n\u003cp\u003eH1.5 hex wrench\u003c\/p\u003e\n\u003cp\u003ePH2 Philips screwdriver\u003c\/p\u003e\n\u003cp\u003e30 minutes of your time\u003c\/p\u003e\n\u003ch3\u003eSafety Warning\u003cbr\u003eIMPORTANT!\u003c\/h3\u003e\n\u003cp\u003eIt's crucial to power off the printer before performing any maintenance work on the printer and its electronics, including tool head wires, because leaving the printer on while conducting such tasks can cause a short circuit, which can lead to additional electronic damage and safety hazards.\u003c\/p\u003e\n\u003cp\u003eWhen you perform maintenane or troubleshooting on the printer, you may be required to disassemble some parts, including the hotend. This process can expose wires and electrical components that could potentially short circuit if they come into contact with each other or with other metal or electronic components while the printer is still on. This can damage the electronics of the printer and cause further damage.\u003c\/p\u003e\n\u003cp\u003eTherefore, it's essential to switch off the printer and disconnect it from the power source before doing any maintenance work. This will prevent any short circuits or damage to the printer's electronics. By doing so, you can avoid potential damage to the printer's electronic components and ensure that the maintenance work is performed safely and effectively.\u003c\/p\u003e\n\u003ch3\u003eSteps to remove the old Main Controller Board\u003c\/h3\u003e\n\u003ch3\u003e1. Remove the printer's bottom housing cover\u003c\/h3\u003e\n\u003cp\u003ePlace the printer on its side, with the Z axis pillar facing the table.\u003c\/p\u003e\n\u003cp\u003eThen, remove the 16 screws holding the bottom cover in place, to access the Mainboard fan.\u003c\/p\u003e\n\u003cp\u003ePlease note that screws 15 and 16 are different, so keep track of them for when you will re-assemble the bottom cover.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.bambulab.com\/a1m\/replace-mc-board-fan\/remove_bottom_cover_screws_for_a1_mini.jpeg\" alt=\"remove_bottom_cover_screws_for_a1_mini.jpeg\"\u003e\u003c\/p\u003e\n\u003cp\u003eAfter removing the screws, gently pry out the plastic bottom cover.\u003c\/p\u003e\n\u003cp\u003eYou can start from the top right side, and gently work your way around the printer until the cover gets loose.\u003c\/p\u003e\n\u003ch3\u003e2. Remove the Mainboard fan\u003c\/h3\u003e\n\u003cp\u003eStart by removing the two screws holding the fan in place.\u003c\/p\u003e\n\u003cp\u003e\u003cimg alt=\"remove_a1_mini_mc_board_fan_screws.jpeg\" src=\"https:\/\/wiki.bambulab.com\/a1m\/replace-mc-board-fan\/remove_a1_mini_mc_board_fan_screws.jpeg\"\u003e\u003c\/p\u003e\n\u003cp\u003eWith the screws removed, gently pull the fan towards you and locate the fan cable connector.\u003c\/p\u003e\n\u003cp\u003eGently pull on the fan connector to disconnect the cable from the Mainboard.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.bambulab.com\/a1m\/replace-mc-board-fan\/disconnect_mc_fan_connector.jpeg\" alt=\"disconnect_mc_fan_connector.jpeg\"\u003e\u003c\/p\u003e\n\u003ch3\u003e3. Remove the USB C cable bracket and disconnect it\u003c\/h3\u003e\n\u003cp\u003eWith the cover removed, we can proceed in removing the USB C cable bracket as shown in the image below. \u003c\/p\u003e\n\u003cp\u003eThis is used to hold the USB cable securely attached to the main board.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.bambulab.com\/a1m\/replace-usb-c-cable\/unscrew_the_usb_cable_bracket.jpeg\" alt=\"unscrew_the_usb_cable_bracket.jpeg\"\u003e\u003c\/p\u003e\n\u003cp\u003eWith the screws removed, you can gently disconnect it. Please make sure to pull towards the right, and not bend the cable as there is a small risk of damaging the USB connector on the board.\u003c\/p\u003e\n\u003cp\u003e\u003cimg alt=\"remove_the_a1_mini_usb_cable.jpeg\" src=\"https:\/\/wiki.bambulab.com\/a1m\/replace-usb-c-cable\/remove_the_a1_mini_usb_cable.jpeg\"\u003e\u003c\/p\u003e\n\u003ch3\u003e4. Disconnect the Wi-Fi Antenna connector\u003c\/h3\u003e\n\u003cp\u003eIn the next step, gently pull the Wi-Fi Antenna cable towards you. Use a flat tool to carefully remove it.\u003c\/p\u003e\n\u003cp\u003eTake extra care at this step to pull it upwards from the board to avoid damaging the Mainboard.\u003c\/p\u003e\n\u003cp\u003e\u003cimg alt=\"disconnect_the_wi-fi_antenna_connector.jpeg\" src=\"https:\/\/wiki.bambulab.com\/a1m\/replace-wifi-antenna\/disconnect_the_wi-fi_antenna_connector.jpeg\"\u003e\u003c\/p\u003e\n\u003ch3\u003e5. Disconnect the ribbon cable of the Touchscreen\u003c\/h3\u003e\n\u003cp\u003eIn the next step, gently pull the plastic clip holding the ribbon cable towards you. It will release the ribbon cable so you can pull it out\u003c\/p\u003e\n\u003cp\u003eTake extra care at this step. The clip can be easily damaged\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.bambulab.com\/a1m\/replace-touchscreen\/open_the_plastic_clip_of_the_ribbon_cable.jpeg\" alt=\"open_the_plastic_clip_of_the_ribbon_cable.jpeg\"\u003e\u003c\/p\u003e\n\u003ch3\u003e6. Remove the remaining Mainboard cables\u003c\/h3\u003e\n\u003cp\u003eYou can now remove the remaining Mainboard cables.\u003c\/p\u003e\n\u003cp\u003ePlease take extra care with the cables labeled 4 and 5. They have a small clip on the bottom section that needs to be pressed when removing them.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.bambulab.com\/a1m\/remove-mc-board\/disconnect_the_remaining_wires.jpeg\" alt=\"disconnect_the_remaining_wires.jpeg\"\u003e\u003c\/p\u003e\n\u003ch3\u003e7. Remove the plastic wire cover\u003c\/h3\u003e\n\u003cp\u003eCarefully remove the three screws holding the plastic wire cover in place to access the power terminals of the Power Supply.\u003c\/p\u003e\n\u003cp\u003ePlease note that screw nr. 3 is on the side.\u003c\/p\u003e\n\u003cp\u003e\u003cimg alt=\"remove_the_plastic_wire_cover.jpeg\" src=\"https:\/\/wiki.bambulab.com\/a1m\/power-supply\/remove_the_plastic_wire_cover.jpeg\"\u003e\u003c\/p\u003e\n\u003ch3\u003e8. Remove the Mainboard wires from the power supply\u003c\/h3\u003e\n\u003cp\u003eLoosen the power terminal screws listed in the image below. \u003c\/p\u003e\n\u003cp\u003eSimply make them loose and avoid removing them completely, as it will be easier to re-install everything back in place in the next steps.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.bambulab.com\/a1m\/remove-mc-board\/remove_mc_board_wires_from_the_power_supply.jpeg\" alt=\"remove_mc_board_wires_from_the_power_supply.jpeg\"\u003e\u003c\/p\u003e\n\u003ch3\u003e9. Remove the Mainboard screws and pull out the board\u003c\/h3\u003e\n\u003cp\u003eYou can now remove the three screws holding the board in place. \u003c\/p\u003e\n\u003cp\u003eGently pull the board towards you to remove it from the printer.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.bambulab.com\/a1m\/remove-mc-board\/mc_board_a1_mini_screws.jpeg\" alt=\"mc_board_a1_mini_screws.jpeg\"\u003e\u003c\/p\u003e\n\u003ch3\u003e10. Remove the heatbed cable wires from the Mainboard\u003c\/h3\u003e\n\u003cp\u003eThe final step in the removal of the Mainboard is to remove the heatbed cable wires from it. \u003c\/p\u003e\n\u003cp\u003eThe wires have a secure latch to hold them well-connected, so you will need to push on the small metallic clip when pulling the wires.\u003c\/p\u003e\n\u003cp\u003e\u003cimg alt=\"remove_the_heatbed_wires_on_a1.jpeg\" src=\"https:\/\/wiki.bambulab.com\/a1m\/remove-mc-board\/remove_the_heatbed_wires_on_a1.jpeg\"\u003e\u003c\/p\u003e\n\u003cp\u003eThe Mainboard is now removed.\u003c\/p\u003e\n\u003ch3\u003eSteps to install the new Main Controller Board\u003c\/h3\u003e\n\u003ch3\u003e1. Install the new Mainboard\u003c\/h3\u003e\n\u003cp\u003eBefore you start the procedure, please take a picture of the QR code located on the back side of the board. \u003cbr\u003eYou will need it after the replacement is completed.\u003c\/p\u003e\n\u003cp\u003eThe content of this QR code is the complete machine SN serial number, which is used to register the device after replacing the mainboard.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.bambulab.com\/a1m\/remove-mc-board\/ap_board_a1_sn.jpeg\" alt=\"ap_board_a1_sn.jpeg\"\u003e\u003c\/p\u003e\n\u003cp\u003eProceed to install the new Mainboard and attach it with the three screws to the printer frame\u003c\/p\u003e\n\u003cp\u003e\u003cimg alt=\"mc_board_a1_mini_screws.jpeg\" src=\"https:\/\/wiki.bambulab.com\/a1m\/remove-mc-board\/mc_board_a1_mini_screws.jpeg\"\u003e\u003c\/p\u003e\n\u003ch3\u003e2. Re-connect the heatbed cables to the Mainboard\u003c\/h3\u003e\n\u003cp\u003eCarefully re-connect the heatbed wires to the Mainboard. The Black wire is on the top, the Red wire is on the bottom. \u003c\/p\u003e\n\u003cp\u003ePush the rubber insulation over the heatbed wire connectors, then re-connect the thermistor cable.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.bambulab.com\/a1m\/remove-mc-board\/re-connect_the_heatbed_cable_wires.jpeg\" alt=\"re-connect_the_heatbed_cable_wires.jpeg\"\u003e\u003c\/p\u003e\n\u003ch3\u003e3. Re-connect the Mainboard power terminal wires\u003c\/h3\u003e\n\u003cp\u003eCarefully re-connect the power terminal wires as shown below and tighten the screws.\u003cbr\u003eThe wire information is as follows:\u003c\/p\u003e\n\u003cp\u003e1.  -V Mainboard Wire (Black)\u003c\/p\u003e\n\u003cp\u003e2. +V Mainboard Wire (Red)\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.bambulab.com\/a1m\/remove-mc-board\/mc_board_power_wires_on_a1_mini.jpeg\" alt=\"mc_board_power_wires_on_a1_mini.jpeg\"\u003e\u003c\/p\u003e\n\u003ch3\u003eIMPORTANT\u003c\/h3\u003e\n\u003cp\u003eAfter installing all the wires as shown in the image below, ensure there is no movement and all the wires are fixed in place\u003c\/p\u003e\n\u003ch3\u003e4. Install the screws holding the plastic wire cover in place.\u003c\/h3\u003e\n\u003cp\u003eArrange the wires coming from the heatbed cable and power cable as shown in the image, then re-attach the plastic cover back to the printer using the three screws\u003cbr\u003eThese screws will be threaded inside plastic standoffs. Avoid over-tightening them as you can damage the plastic threads.\u003c\/p\u003e\n\u003cp\u003e\u003cimg alt=\"remove_the_plastic_wire_cover.jpeg\" src=\"https:\/\/wiki.bambulab.com\/a1m\/power-supply\/remove_the_plastic_wire_cover.jpeg\"\u003e\u003c\/p\u003e\n\u003ch3\u003e5. Re-connect the remaining Mainboard cables\u003c\/h3\u003e\n\u003cp\u003eYou can now re-connect the remaining Mainboard cables.\u003c\/p\u003e\n\u003cp\u003e1. Z-axis motor\u003c\/p\u003e\n\u003cp\u003e2. X-axis motor\u003c\/p\u003e\n\u003cp\u003e3. Y axis motor\u003c\/p\u003e\n\u003cp\u003e4. Eddy Sensor\u003c\/p\u003e\n\u003cp\u003e5. Live View Camera\u003c\/p\u003e\n\u003cp\u003e\u003cimg alt=\"disconnect_the_remaining_wires.jpeg\" src=\"https:\/\/wiki.bambulab.com\/a1m\/remove-mc-board\/disconnect_the_remaining_wires.jpeg\"\u003e\u003c\/p\u003e\n\u003ch3\u003e6. Re-connect the ribbon cable of the Touchscreen\u003c\/h3\u003e\n\u003cp\u003eGently re-connect the ribbon cable, ensuring the white line aligns to the outline marked on the board. \u003c\/p\u003e\n\u003cp\u003eWhen everything looks good, simply flip the clip towards the right to lock the ribbon cable in place.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.bambulab.com\/a1m\/replace-touchscreen\/re-install_the_ribbon_cable_of_the_screen.jpeg\" alt=\"re-install_the_ribbon_cable_of_the_screen.jpeg\"\u003e\u003c\/p\u003e\n\u003ch3\u003e7. Re-connect the the Wi-Fi Antenna connector\u003c\/h3\u003e\n\u003cp\u003eGently re-connect the round Wi-Fi antenna connector to the Mainboard. Take extra care when installing it.\u003c\/p\u003e\n\u003cp\u003eThe Wi-Fi antenna connector has a very small pin on the middle which can be damaged if the connector is not carefully aligned.\u003c\/p\u003e\n\u003cp\u003e\u003cimg alt=\"mc_board_wi-fi_connector.jpeg\" src=\"https:\/\/wiki.bambulab.com\/a1m\/replace-wifi-antenna\/mc_board_wi-fi_connector.jpeg\"\u003e\u003c\/p\u003e\n\u003cp\u003eIf everything is carefully aligned, the Wi-Fi antenna cable will clip in place, and look like this:\u003c\/p\u003e\n\u003cp\u003e\u003cimg alt=\"a1_mini_wi-fi_antenna.jpg\" src=\"https:\/\/wiki.bambulab.com\/a1m\/replace-wifi-antenna\/a1_mini_wi-fi_antenna.jpg\"\u003e\u003c\/p\u003e\n\u003ch3\u003e8. Connect the USB C cable and re-attach the bracket\u003c\/h3\u003e\n\u003cp\u003eCarefully route the USB cable towards the USB header on the board, and re-install it as shown below.\u003c\/p\u003e\n\u003cp\u003eThen, re-attach the metallic bracket with the screws we removed before.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.bambulab.com\/a1m\/replace-usb-c-cable\/scr-20240131-lcue-2.jpeg\" alt=\"scr-20240131-lcue-2.jpeg\"\u003e\u003c\/p\u003e\n\u003ch3\u003e9. Install the Mainboard fan\u003c\/h3\u003e\n\u003cp\u003eYou can now install the Mainboard fan connector to the Mainboard\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.bambulab.com\/a1m\/replace-mc-board-fan\/disconnect_mc_fan_connector.jpeg\" alt=\"disconnect_mc_fan_connector.jpeg\"\u003e\u003c\/p\u003e\n\u003cp\u003eNext, attach the fan to the Mainboard heatsink using the two screws.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.bambulab.com\/a1m\/replace-mc-board-fan\/remove_a1_mini_mc_board_fan_screws.jpeg\" alt=\"remove_a1_mini_mc_board_fan_screws.jpeg\"\u003e\u003c\/p\u003e\n\u003ch3\u003e10. Perform some wire management\u003c\/h3\u003e\n\u003cp\u003eBefore putting the bottom cover back in place, ensure that the Mainboard wires are routed correctly, so they do not interfere with the Mainboard fan, as shown in the image below.\u003c\/p\u003e\n\u003cp\u003e\u003cimg alt=\"a1_mini_board_and_wire_managemet.jpg\" src=\"https:\/\/wiki.bambulab.com\/a1m\/replace-usb-c-cable\/a1_mini_board_and_wire_managemet.jpg\"\u003e\u003c\/p\u003e\n\u003ch3\u003e11. Install the back cover\u003c\/h3\u003e\n\u003cp\u003eYou can now proceed with installing the bottom cover back to the printer.\u003c\/p\u003e\n\u003cp\u003eStart by tightening screws 15 and 16 to ensure the side wire loom sits correctly.\u003c\/p\u003e\n\u003cp\u003eThen, proceed with installing the other remaining screws, while ensuring you do not over-tighten them.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.bambulab.com\/a1m\/replace-mc-board-fan\/remove_bottom_cover_screws_for_a1_mini.jpeg\" alt=\"remove_bottom_cover_screws_for_a1_mini.jpeg\"\u003e\u003c\/p\u003e\n\u003cp\u003eDue to changes in the fan placement on the updated 2025 mainboard, the older version of the A1 mini back cover may not fully close during installation.\u003c\/p\u003e\n\u003cp\u003eAs shown in the image below, you will need to manually trim the marked area to ensure the back cover can be properly closed.\u003c\/p\u003e\n\u003cp\u003e\u003cimg alt=\"a1_mini_新背板修剪_1.jpg\" src=\"https:\/\/wiki.bambulab.com\/a1-mini\/a1mini-replace-mc-board-fan\/a1_mini_%E6%96%B0%E8%83%8C%E6%9D%BF%E4%BF%AE%E5%89%AA_1.jpg\"\u003e\u003c\/p\u003e\n\u003ch3\u003eVerify the functionality\u003c\/h3\u003e\n\u003cp\u003eTo ensure everything works as expected, turn on the printer and perform a homing procedure.\u003c\/p\u003e\n\u003cp\u003eTry to home the axis, and confirm the temperatures are correctly displayed on the screen.\u003c\/p\u003e\n\u003cp\u003eIf everything is confirmed to be working, this confirms the Mainboard installation was correct.\u003c\/p\u003e\n\u003ch3\u003eCheck the indicator lights on the control board\u003c\/h3\u003e\n\u003cp\u003eNormal State: the MC board and AP board are integrated into the mainboard\u003c\/p\u003e\n\u003cp\u003eThe MC board flashes green once every 5 seconds\u003c\/p\u003e\n\u003cp\u003eThe AP board has 1 green indicator light that flashes once per second\u003c\/p\u003e\n\u003ch3\u003ePrinter SN Registration\u003c\/h3\u003e\n\u003cp\u003eAfter this procedure is completed, the printer will have its original Serial Number, and you will be able to bind it to your account.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.bambulab.com\/a1m\/remove-mc-board\/ap_board_a1_sn.jpeg\" alt=\"ap_board_a1_sn.jpeg\"\u003e\u003c\/p\u003e\n\u003ch3\u003eImportant Note:\u003c\/h3\u003e\n\u003cp\u003eOnce the new serial number (SN) is successfully registered, the old SN will be invalidated, and the old AP board can no longer be registered or bound.\u003c\/p\u003e\n\u003cp\u003eFor machines that have had the AP board replaced, as the new SN is not registered, binding cannot be performed. We recommend skipping the binding process during the initial startup to test if the replacement fixed the problem (unless you are troubleshooting network issues).\u003c\/p\u003e\n\u003cp\u003e\u003cimg\u003e\u003cimg src=\"https:\/\/wiki.bambulab.com\/x2d\/maintenance\/ap-board\/register_sn_en.jpg\" alt=\"register_sn_en.jpg\"\u003e\u003c\/p\u003e\n\u003ch3\u003eCalibration step after the operation\u003c\/h3\u003e\n\u003cp\u003eA full calibration is required after the Main Controller Board replacement procedure.\u003c\/p\u003e\n\u003ch3\u003ePotential problems and solutions\u003c\/h3\u003e\n\u003cp\u003eIf you encounter problems during the installation of a new Motherboard, please check the potential problems and solutions listed below:\u003c\/p\u003e\n\u003ch3\u003eThe printer doesn't power on\u003c\/h3\u003e\n\u003cp\u003eConfirm the Motherboard power wires are installed correctly, as shown in Step 3. Re-connect the Mainboard power terminal wires\u003c\/p\u003e\n\u003ch3\u003eThe heatbed temperature is not reported \/ shows 0C\u003c\/h3\u003e\n\u003cp\u003eCheck the heatbed cables shown in Step 2 Re-connect the heatbed wires, and confirm the Green and White wire connector is fully inserted in the Motherboard.\u003c\/p\u003e\n\u003ch3\u003eThe heatbed is not heating\u003c\/h3\u003e\n\u003cp\u003eCheck the heatbed cables shown in Step 2 Re-connect the heatbed wires, and confirm the Red and Black wires are fully inserted in the Motherboard.\u003c\/p\u003e\n\u003ch3\u003eOne of the axis is not working\u003c\/h3\u003e\n\u003cp\u003eCheck the motor wires and confirm they are installed correctly, as shown in Step 5. Re-connect the remaining Mainboard cables\u003c\/p\u003e\n\u003ch3\u003eThe printer cannot be connected to your Bambu Lab Account\u003c\/h3\u003e\n\u003cp\u003eThe new board will need to be registered by \u003cbr\u003eCustomer Support. \u003c\/p\u003e\n\u003cp\u003eTo do so, provide a picture of the Main Controller board QR code (the one located on the back side of the board) and wait for a confirmation.\u003c\/p\u003e\n\u003cp\u003e\u003cimg alt=\"ap_board_a1_sn.jpeg\" src=\"https:\/\/wiki.bambulab.com\/a1m\/remove-mc-board\/ap_board_a1_sn.jpeg\"\u003e\u003c\/p\u003e\n\u003ch3\u003eA1 Mini Mainboard Connectors\u003c\/h3\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/wiki.bambulab.com\/a1m\/remove-mc-board\/a1_mini_mainboard.png\" alt=\"a1_mini_mainboard.png\"\u003e\u003c\/p\u003e\n\u003cp\u003e1.USB-C to TH Board Connector\u003c\/p\u003e\n\u003cp\u003e2.Touchscreen Connector\u003c\/p\u003e\n\u003cp\u003e3.Y-Motor Connector\u003c\/p\u003e\n\u003cp\u003e4.X-Motor Connector\u003c\/p\u003e\n\u003cp\u003e5.Z-Motor Connector\u003c\/p\u003e\n\u003cp\u003e6.Eddy Sensor Connector\u003c\/p\u003e\n\u003cp\u003e7.Live View Camera Connector\u003c\/p\u003e\n\u003cp\u003e8.MC Board Cooling Fan Connector\u003c\/p\u003e\n\u003cp\u003e9.Power Input Wires\u003c\/p\u003e\n\u003cp\u003e10.Power Output Connectors for Heatbed\u003c\/p\u003e\n\u003cp\u003e11.Heatbed Signal Cable Connectors\u003c\/p\u003e\n\u003cp\u003e12.AMS Lite Connectors\u003c\/p\u003e\n\u003cp\u003e13.SD Card\u003c\/p\u003e","brand":"Bambu Lab","offers":[{"title":"Default Title","offer_id":53729082769721,"sku":null,"price":79.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0759\/4531\/2569\/files\/6391ace427ade714b70fb966024ae804_7d93565e-c3c5-4582-8447-1ee1c088a1c2.jpg?v=1783331512","url":"https:\/\/p3d.mx\/es\/products\/mainboard-for-bambu-a1-mini","provider":"P3D","version":"1.0","type":"link"}